SWITNEX AC85-250V RF Wireless Remote Control Switch User Manual
SWITNEX AC85-250V RF Wireless Remote Control Switch User Manual
| Technical Data | |
|---|---|
| Brand | SWITNEX |
| Model Number | 2 Buttons |
| Connections | Wireless |
| Terminal Type | Clamp |
| Compatible Devices | AC |
| Remote Battery Type | Lithium Manganese Dioxide (CR2032) |
| Operating Modes | Momentary, Toggle, Latched |
| Max Power | 2500 Watts |
| Working Voltage | AC 85V-250V |
| Output Voltage | 1V-250V |
| Current Rating | 10A |
| Contact Material | Copper |
| Contact Type | Normally Open (NO) |
| Mounting Type | Wall Mount |
| Frequency | 433MHz |
| Code Type | 1527 Learning Code or 2262 Fixed Code |
Product Detail
- 1 x SWITNEX 433MHz RF Relay Receiver Module – with protective casing
- 2 x 2-Button Remote Controls – each with buttons A and B, powered by CR2032 battery
- Terminals: N (Neutral input), L (Live input), NO (Normally Open), COM (Common), NC (Normally Closed)
- Learning button on receiver – for programming modes and resetting
- Indicator light on receiver – provides visual feedback
Wiring Diagram
- N terminal: Neutral wire input (AC power source)
- L terminal: Live wire input (AC power source)
- NO/COM/NC terminals: Output connections to device
- AC device: Connect power source to L/N; device to COM and NO
- DC device: Connect AC power to L/N; DC power supply output to COM/NO (observe polarity)
- AC motor (rolling shutters): Connect motor Up wire to one NO, Down wire to another NO, common wire to corresponding COM
- DC motor: Connect DC power supply output to COM terminals; motor positive/negative to NO terminals
Warning
- Always disconnect power before installing or servicing the device. Improper wiring can lead to electric shock or fire.
- Installation should be performed by a qualified electrician or knowledgeable individual.
- Ensure the operating voltage of your device matches the receiver specifications (AC 85V-250V).
- Do not exceed the maximum current rating of 10A or power rating of 2500W.
- Install the receiver in a dry, well-ventilated area, away from direct sunlight, high temperatures, and corrosive environments.
- Keep remote controls and the receiver out of reach of children.
Operating Mode
Momentary Mode
Press and hold a remote button → relay activated
Release the button → relay deactivated
How to program:
- Press the learning button on the receiver 1 time. The indicator light will flash.
- Press button A on the remote control. The indicator light will flash, confirming successful pairing.
Toggle Mode
Press a remote button once → relay activates and stays on
Press the same button again → relay deactivates
How to program:
- Press the learning button on the receiver 2 times. The indicator light will flash.
- Press button A on the remote control. The indicator light will flash, confirming successful pairing.
Latched Mode
Press button A → Relay 1 activates
Press button B → Relay 2 activates, and Relay 1 deactivates simultaneously
How to program:
- Press the learning button on the receiver 3 times. The indicator light will flash.
- Press button A on the remote control (program Relay 1).
- Press button B on the remote control (program Relay 2). The indicator light will flash, confirming successful pairing.
Reset
To clear all programmed remote controls from the receiver, press the learning button 8 times consecutively. The indicator light will flash rapidly and then turn off, indicating that all stored codes have been cleared. After reset, reprogram your remotes following the steps above.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Relay clicks but device does not activate | Incorrect wiring between output terminals (NO, COM, NC) and device; Device malfunction | Check wiring connections; Test device by powering directly |
| Device not responding to remote | No power to receiver; Remote battery low/dead; Remote not programmed; Receiver reset | Check power supply; Replace CR2032 battery; Re-program remote; Reset and re-pair if needed |
| Reduced remote control range | Low remote battery; Environmental interference; Obstructions | Replace CR2032 battery; Minimize interference; Ensure clear line of sight |
Maintenance
- Keep the receiver module and remote controls clean and dry.
- Avoid exposing them to extreme temperatures, humidity, or corrosive substances.
- Do not attempt to repair internal components yourself; contact qualified personnel if service is required.
- Replace remote battery when range decreases or LED dims (use CR2032 lithium cell, positive side up).
Contact
- Email: linktrol@icloud.com
- WhatsApp: +86 15812381273
If there is any question about the products, please contact us first. We will do our best to solve your problem. Thank you.
10% OFF
For an exclusive 10% OFF upgrade discount, Use code: FBA10.
Copy the code before visiting the shop.