SWITNEX Waterproof Wireless Remote Control DC 8V-80V 30A Radio Control Switch User Manual

SWITNEX Waterproof Wireless Remote Control DC 8V-80V 30A Radio Control Switch User Manual

Technical Data
Receiver Working VoltageDC 8V~80V
Quiescent Current<5MA
Max Current30A
RF frequency433MHz
Working temperature-30~+80℃
Receiving Sensitivity>97dbm
Storage remote controlsUp to 20 pieces
Support encoding1527 Leaning code
RF Operating modeASK superheterodyne wireless reception
Receiving rangeOpen space is more than 50 meters
Waterproof GradeIP65
Remote operating modeMomentary / Toggle / Latched
Transmitter Battery2x CR2016 (included)

Product Detail

Waterproof Receiver and Two Transmitters

  • Receiver unit – IP65 waterproof rating, suitable for outdoor/wet locations
  • 2 x Transmitters – remote controls with ON/OFF buttons, 2x CR2016 batteries included
  • Learning button on receiver – for programming modes and resetting
  • Indicator LED on receiver – provides visual feedback
  • Antenna on receiver – extend for better signal reception
  • Input/Output terminals – clearly marked for DC 8V-80V connections (V- V+ input, V+ V- output)

Wiring Diagram

Wiring Connections for DC 8V-80V Wire Connection Steps using Heat Shrink Solder Connectors

  • Input: Connect DC 8V-80V power supply to V- (negative) and V+ (positive) input terminals
  • Output: Connect device to V+ and V- output terminals
  • Use heat shrink solder connectors for secure waterproof connections (strip 5-7mm, insert, heat with heat gun, cool 1 minute)

Warning

  • Always disconnect power before performing any wiring or maintenance.
  • Ensure all wiring connections are secure and properly insulated.
  • Do not exceed the maximum current rating of 30A.
  • The product is IP65 waterproof, but avoid prolonged submersion in water.
  • Keep remote controls away from children.
  • Usually the receiver and transmitter have been paired in factory. If not, reprogram them.
  • Reset before you want to change the operating mode.
  • After reset, all remote controls cannot work anymore.
  • Replace the battery in time when the remote transmitter voltage is low.
  • Slightly stretch the antenna on the receiver for better signal reception.

Operating Mode

The product is pre-set to Latched mode by default. Follow the steps below to change modes.

Momentary Mode

Press and hold a button → relay turns ON
Release the button → relay turns OFF

How to program:

  1. Press the learning button on the receiver 1 time. Wait 3 seconds.
  2. Press the ON button on the transmitter. Wait 3 seconds.
  3. Press the OFF button on the transmitter. Setup complete.

Toggle Mode

Press a button once → relay turns ON
Press the same button again → relay turns OFF

How to program:

  1. Press the learning button on the receiver 2 times. Wait 3 seconds.
  2. Press the ON button on the transmitter. Wait 3 seconds.
  3. Press the OFF button on the transmitter. Setup complete.

Latched Mode (Default)

Press ON button → relay turns ON
Press OFF button → relay turns OFF

How to program:

  1. Press the learning button on the receiver 3 times. Wait 3 seconds.
  2. Press the ON button on the transmitter. Wait 3 seconds.
  3. Press the OFF button on the transmitter. Setup complete.

Reset

To clear all paired remote controls from the receiver’s memory, press the learning button 8 times consecutively. The reset is successful. After reset, previously paired remote controls will no longer function. Wire Connection Steps using Heat Shrink Solder Connectors

Troubleshooting

If the receiver and transmitter cannot operate normally, try the following steps:

  • No response from receiver: Check power supply (DC 8V-80V). Ensure transmitter batteries are not depleted. Verify pairing (re-pair if needed). Check for obstructions or excessive distance.
  • Intermittent operation: Weak transmitter battery (replace). Interference from other RF devices. Extend receiver antenna.
  • Incorrect operating mode: Reprogram the desired mode (see Operating Mode).

Maintenance

  • Cleaning: Wipe with a soft, dry cloth. Do not use liquid cleaners.
  • Battery replacement: Replace transmitter batteries (2x CR2016) when range decreases or LED dims. Ensure correct polarity.
  • Waterproofing: Check seals periodically. Keep connector points dry and secure.
  • Storage: Store in a cool, dry place when not in use.

Contact

If there is any question about the products, please contact us first. We will do our best to solve your problem. Thank you.

10% OFF

For an exclusive 10% OFF upgrade discount, Use code: FBA10.

Copy the code before visiting the shop.