SITNEX Waterproof Wireless Remote Control Switch (AC 85V-250V, 30A) User Manual
SITNEX Waterproof Wireless Remote Control Switch (AC 85V-250V, 30A) User Manual
| Technical Data | |
|---|---|
| Receiver Working Voltage | AC 85V~250V |
| Quiescent Current | <5MA |
| Max Current | 30A |
| RF frequency | 433MHz |
| Working temperature | -30~+80℃ |
| Receiving Sensitivity | >97dbm |
| Storage remote controls | Up to 20 pieces |
| Support encoding | 1527 Leaning code |
| RF Operating mode | ASK superheterodyne wireless reception |
| Receiving range (open space) | More than 50 meters |
| Waterproof Grade | IP65 |
| Remote operating mode | Momentary / Toggle / Latched |
| Transmitter Battery | 2x CR2016 (included) |
| Relay lifespan | Over 100,000 times |
| Max Load Power | 7200 Watts |
| Dimensions (Receiver) | 0.9 x 0.9 x 0.4 cm (0.35 x 0.35 x 0.15 inches) |
| Material | Aluminum |
| Certifications | CE, FCC |
Product Detail
- Receiver unit – IP65 waterproof rating, suitable for indoor and outdoor use (rain and sand resistant), aluminum housing
- 2 x Transmitters – remote controls with ON/OFF buttons, 2x CR2016 batteries included
- 30A high-power relay – can load high-power electrical appliances for long-term stable control
- Learning button on receiver – for programming modes and resetting
- Indicator LED on receiver – provides visual feedback
- Antenna on receiver – extend for better signal reception (improves penetration through walls, floors, doors)
- Input/Output terminals – screw terminals for AC 85V-250V connections (L and N)
Wiring Diagram
- Input: Connect AC 85V-250V Live (L) and Neutral (N) to receiver input terminals
- Output: Connect device (pump, motor, lamp, fan, etc.) to output terminals (L and N)
- Ensure all connections are secure and properly insulated
Warning
- Always disconnect power before performing any wiring or maintenance.
- Ensure all wiring connections are secure and properly insulated.
- Do not exceed the maximum current rating of 30A (7200W).
- The product is IP65 waterproof (resists rain and sand), but do not soak it in water.
- Keep remote controls away from children.
- Usually the receiver and transmitter have been paired in factory. If not, reprogram them.
- Reset before you want to change the operating mode.
- After reset, all remote controls cannot work anymore.
- Replace the battery in time when the remote transmitter voltage is low.
- Slightly stretch the antenna on the receiver for better signal reception.
Operating Mode
The product is pre-set to Latched mode by default. Follow the steps below to change modes.
Momentary Mode
Press and hold a button → relay turns ON
Release the button → relay turns OFF
How to program:
- Press the learning button on the receiver 1 time. Wait 3 seconds.
- Press the ON button on the transmitter. Wait 3 seconds.
- Press the OFF button on the transmitter. Setup complete.
Toggle Mode
Press a button once → relay turns ON
Press the same button again → relay turns OFF
How to program:
- Press the learning button on the receiver 2 times. Wait 3 seconds.
- Press the ON button on the transmitter. Wait 3 seconds.
- Press the OFF button on the transmitter. Setup complete.
Latched Mode (Default)
Press ON button → relay turns ON
Press OFF button → relay turns OFF
How to program:
- Press the learning button on the receiver 3 times. Wait 3 seconds.
- Press the ON button on the transmitter. Wait 3 seconds.
- Press the OFF button on the transmitter. Setup complete.
Reset
To clear all paired remote controls from the receiver’s memory, press the learning button 8 times consecutively. The reset is successful. After reset, previously paired remote controls will no longer function.
Troubleshooting
If the receiver and transmitter cannot operate normally, try the following steps:
- No response from receiver: Check power supply (AC 85V-250V). Ensure transmitter batteries (2x CR2016) are not depleted. Verify pairing (re-pair if needed). Check for obstructions or excessive distance (up to 50m open space).
- Intermittent operation: Weak transmitter battery (replace). Interference from other RF devices. Extend receiver antenna for better signal.
- Incorrect operating mode: Reprogram the desired mode (see Operating Mode).
- Device not activating under high load: Ensure load does not exceed 30A (7200W). Check relay condition (designed for over 100,000 operations).
Maintenance
- Cleaning: Wipe with a soft, dry cloth. Do not use liquid cleaners.
- Battery replacement: Replace transmitter batteries (2x CR2016) when range decreases or LED dims. Ensure correct polarity.
- Waterproofing: IP65 design resists rain and sand, but avoid submersion. Check seals periodically.
- Storage: Store in a cool, dry place when not in use.
Contact
- WhatsApp: +86 15812381273
- Email: linktrol@icloud.com
If there is any question about the products, please contact us first. We will do our best to solve your problem. Thank you.
10% OFF
For an exclusive 10% OFF upgrade discount, Use code: FBA10.
Copy the code before visiting the shop.