SWITNEX DC 12V Wireless Relay Remote Control Switch User Manual
SWITNEX DC 12V Wireless Relay Remote Control Switch User Manual
| Technical Data | |
|---|---|
| Model Number | 1204 |
| Input / Output Volts | 1V-250V |
| Work Volts | DC 12V |
| Current Rating | 10 Amps |
| RF frequency | 433MHz |
| Reception Sensitivity | >97dBm |
| Chip Code | EV1527 (Learning Code) |
| Remote Control Range | Up to 50 meters (open area) |
| Number of Relays | 4 |
| Relay Lifespan | Over 100,000 uses |
| Connector Type | Screw Terminal |
| Contact Material | Copper Alloy |
| Contact Type | Normally Closed (NC), Common (COM), Normally Open (NO) |
| Mounting Type | Surface Mount |
| Product Dimensions | 2.95 x 2.17 x 1.18 inches |
| Product Weight | 5.93 ounces |
| Batteries (Transmitters) | 2 CR2 batteries (included) |
Product Detail
- NO: Normally open pin
- COM: Common pin
- NC: Normally closed pin
Wiring Diagram
Warning
- Usually the receiver and transmitter have been paired with each other in factory. If not, please reprogram them.
- Reset before you want to change the operating mode.
- After reset, all the remote controls cannot work anymore.
- Replace the battery in time when the remote transmitter voltage is low to get stronger signal transmission.
- Slightly stretch the antenna on the receiver for better signal reception.
- Ensure power is disconnected before making any wiring connections.
- The output type is passive output / potential-free contacts.
Operating Mode
Momentary Mode
Press and hold a button → corresponding relay turns on
Release the button → relay turns off
How to program:
- Press the learning button (on the receiver) 1 time. The indicator LED on the receiver will light up.
- Press the desired button (e.g., ‘A’) on the remote transmitter. The indicator LED will flash several times and then turn off. Succeed.
Toggle Mode
Press a button → corresponding relay turns on
Press the same button again → relay turns off
How to program:
- Press the learning button (on the receiver) 2 times. The indicator LED will light up.
- Press the desired button on the remote transmitter. The indicator LED will flash several times and then turn off. Succeed.
Latched Mode
Press button ‘A’ → Relay 1 turns on (Relay 2 turns off if it was on)
Press button ‘B’ → Relay 2 turns on, and Relay 1 turns off at the same time
How to program:
- Press the learning button (on the receiver) 3 times. The indicator LED will light up.
- Press the desired button on the remote transmitter. The indicator LED will flash several times and then turn off. Succeed.
Mixed Mode
For advanced configurations (e.g., 2 momentary + 2 toggle; 2 momentary + 2 latched; 2 toggle + 2 latched), press the learning button 4, 5, or 6 times respectively, then press the corresponding remote buttons as instructed.
Reset
Press the learning button (on the receiver) 8 times. The indicator LED will flash several times and then turn off. Succeed. (All paired transmitters will be cleared.)
Troubleshooting
If the receiver and transmitter cannot operate normally, try the following steps:
- Check if battery power is used up. The indicator LED on the remote transmitter does not light up or is dimly lit. Replace with new CR2 batteries.
- Check if your receiver is wired correctly. Make sure the wiring to NC, COM, NO terminals is correct.
- Ensure the receiver is within range (up to 50 meters in open areas) and the antenna is not obstructed.
- Avoid placing the receiver near other strong RF signal sources that may cause interference.
- Reprogram the receiver and transmitter. Usually this can solve many problems.
- If the problem still remains, please contact us.
Contact
- WA: +15812381273
- Email: linktrol@icloud.com
If there is any question about the products, please contact us first. We will do our best to solve your problem. Thank you.
For an exclusive 10% OFF upgrade discount, Use code: FBA10.
Copy the code before visiting the shop.