SWITNEX RF 433MHz Wireless Light Switch System User Manual
SWITNEX RF 433MHz Wireless Light Switch System User Manual
| Technical Data | |
|---|---|
| Model Number | 750828381477 |
| Product Dimensions (Switch) | 8.8 x 8.8 x 2.3 cm |
| Product Weight (Switch) | 60 grams |
| Receiver Dimensions | 4.7 x 4.2 x 2.3 cm |
| Operating Voltage (Receiver) | AC 85V ~ 250V |
| Current Rating (Receiver) | 10 A |
| RF frequency | 433 MHz |
| Learning Code | EV1527 |
| Switch Battery | 1 x 12V 27A (included) |
| Switch Lifespan | Over 500,000 clicks |
| Receiver Relay Lifespan | Over 400,000 uses |
| Material | Plastic |
| Switch Type | Push Button |
| Terminal Type | Screw |
| Country of Origin | China |
Product Detail
- Receiver terminals: Input L / Input N (from power source), Output L / Output N (to appliance)
- Learning button on receiver – for pairing and resetting
- Indicator light on receiver – provides visual feedback during programming
- Antenna on receiver – can be extended for stronger signal
Wiring Diagram
Warning
- Always disconnect power at the circuit breaker before installing or servicing any electrical components.
- Installation should be performed by a qualified electrician or in accordance with local electrical codes.
- Do not exceed the maximum load rating of 10A for the receiver.
- Ensure all wire connections are secure to prevent electrical hazards.
- Keep the device away from water and extreme temperatures.
- The wireless switch requires no wiring – can be mounted with adhesive tape or screws.
Operating Mode
Toggle Mode
Press the button on the wireless switch → light turns ON
Press the same button again → light turns OFF
How to program (pairing):
- Ensure the receiver is powered on.
- Press the learning button on the receiver 2 times. Wait 3 seconds. The indicator light on the receiver will blink.
- Press the button on the wireless switch. Wait 3 seconds. The indicator light will stop blinking, indicating successful pairing.
Multi-Control Scenarios
- Multiple switches control one lamp: Pair up to 10 wireless switches with a single receiver (3-way switch setup).
- One switch controls multiple lamps: Pair a single wireless switch with multiple receivers for simultaneous control.
Reset
Press the learning button on the receiver 8 times. Wait 3 seconds. The indicator light will blink rapidly and then turn off, indicating that all paired devices have been cleared.
Troubleshooting
If the receiver and transmitter cannot operate normally, try the following steps:
- Weak signal reception: Extend the antenna on the receiver. Ensure the switch battery is not depleted. Verify the switch and receiver are within effective range (up to 50 meters in open areas).
- Switch not responding: Check the 12V 27A battery. Replace if necessary. Re-pair the switch with the receiver (see Operating Mode > How to program).
- Receiver not toggling: Confirm wiring is correct (Input L/N to power source, Output L/N to appliance). Ensure the load does not exceed 10A.
- Reset receiver (press learning button 8 times) to clear all pairings, then re-pair.
Maintenance
- Battery replacement (wireless switch): The 12V 27A battery typically lasts about 5 years. Carefully open the switch casing, remove the old battery, insert a new one with correct polarity, and close securely.
- Cleaning: Wipe the switch and receiver with a soft, dry cloth. Do not use abrasive cleaners or immerse in water.
Contact
- Email: linktrol@icloud.com
- WhatsApp: +86 15812381273 Refer to the product packaging or the retailer’s website for customer support contact information.
If there is any question about the products, please contact us first. We will do our best to solve your problem. Thank you.
10% OFF
For an exclusive 10% OFF upgrade discount, Use code: FBA10.
Copy the code before visiting the shop.