SWITNEX Wireless DC Motor Remote Control Switch User Manual
SWITNEX Wireless DC Motor Remote Control Switch User Manual
| Technical Data | |
|---|---|
| Input Voltage | DC 12V-80V |
| Max Load (Resistive) | 10 Amps |
| Max Load (Inductive) | 5 Amps |
| Frequency | 433MHz |
| Operating Modes | Momentary, Toggle, Latched |
| Transmitter Storage | Up to 20 transmitters |
| Control Distance | 20-50 meters (open area) |
| Relay Lifespan | >100,000 times |
| Item Weight | 4.2 ounces |
| Package Dimensions | 4.02 x 3.74 x 1.57 inches |
| Batteries | 2 x 12V batteries (included) |
Product Detail
- Learning button on receiver – for programming operating modes and resetting
- Indicator light on receiver – provides visual feedback
Wiring Diagram
- Input: DC 12V-80V power supply (red: positive, black: negative)
- Output: To DC motor (red: motor positive, black: motor negative)
- For winch applications: See specialized winch solenoid relay wiring diagram.
Warning
- Ensure the power supply voltage matches the receiver’s specified voltage range (DC 12V-80V).
- Do not exceed the maximum resistive load of 10A (inductive load 5A) for the relay.
- Disconnect power before performing any wiring or maintenance to prevent electric shock.
- Keep the device away from water and high humidity environments.
- Do not attempt to disassemble or modify the device, as this may void the warranty and pose safety risks.
- This product is intended for use with DC motors only.
Operating Mode
The product is typically pre-programmed in Latched mode. You can change the mode by following the programming steps below.
Momentary Mode
Press and hold the Up (▲) button → motor operates forward
Release the button → motor stops
How to program:
- Press the learning button on the receiver 1 time. The indicator light will flash once.
- Press the Up (▲) button on the transmitter. The indicator light will flash, confirming successful programming.
Toggle Mode
Press the Up (▲) button once → motor starts (forward)
Press the same button again → motor stops
How to program:
- Press the learning button on the receiver 2 times. The indicator light will flash twice.
- Press the Up (▲) button on the transmitter. The indicator light will flash, confirming successful programming.
Latched Mode
Press Up (▲) → motor rotates forward
Press Down (▼) → motor rotates reverse
Press Stop (■) → motor stops
How to program:
- Press the learning button on the receiver 3 times. The indicator light will flash three times.
- Press the Up (▲) button on the transmitter (program forward rotation).
- Press the Down (▼) button on the transmitter (program reverse rotation).
- Press the Stop (■) button on the transmitter (program stop function). The indicator light will flash, confirming successful programming.
Change Motor Direction (Advanced)
If the motor rotates opposite to the desired direction for Up/Down buttons, press the learning button 7 times. This will swap the output polarity.
Reset
To clear all programmed transmitters and reset the receiver to default state, press the learning button 8 times. The indicator light will flash to confirm. After reset, no remote controls will operate the receiver until they are re-programmed.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Motor does not respond to remote | No power to receiver; Transmitter batteries low/dead; Transmitter not programmed; Receiver reset | Check power supply; Replace transmitter batteries; Re-program transmitter (see Operating Mode) |
| Motor operates in wrong direction | Incorrect wiring; Motor polarity reversed | Verify wiring (see Wiring Diagram); Use motor direction change function (press learning button 7 times) |
| Reduced remote control range | Low transmitter battery; Environmental interference; Obstructions | Replace transmitter batteries; Minimize interference sources; Ensure clear line of sight if possible |
| Motor runs continuously or does not stop | Incorrect operating mode programmed; Faulty transmitter button | Verify and re-program desired mode; Test with another transmitter if available |
Maintenance
- Keep the receiver and transmitters clean and dry.
- Regularly check wiring connections for looseness or corrosion.
- Replace transmitter batteries when the indicator light dims or range decreases. The transmitters use 12V batteries.
- Do not expose the devices to extreme temperatures or direct sunlight for prolonged periods.
Contact
- Email: linktrol@icloud.com
- WhatsApp: +86 15812381273 Refer to the product packaging or the retailer’s website for customer support contact information.
If there is any question about the products, please contact us first. We will do our best to solve your problem. Thank you.
For an exclusive 10% OFF upgrade discount, Use code: FBA10.
Copy the code before visiting the shop.